How long will this copy take? Finder's time remaining, explained
Finder says "About 5 minutes", then "About an hour", then nothing at all. Here is what that estimate is based on, how to see the real speed, and how to work out a steadier figure yourself.
Updated 10 November 2026
The short answer
Finder's “time remaining” is a running estimate: what is left to copy, divided by how fast the copy has been going lately. When the speed changes, the estimate changes with it, which is why it swings about.
Finder never shows the speed itself. To see it, open Activity Monitor and look at the Disk tab. For a steadier estimate, divide what is left by the speed you see there.
Where Finder shows the time remaining
The estimate is in Finder's progress window, on the line under each copy: how much has been copied (for example “7.6 GB of 12 GB”) followed by the time left (“About 4 minutes”). If the window has gone behind something, choose Window → Show Progress Window in Finder to bring it back.
At the start you may see “Preparing to copy” or “Estimating time remaining” instead. Finder is counting the files and needs a few seconds of steady copying before it can guess. If it sits there for a long time, see our guide on telling a slow copy from a stuck one.
Why the estimate jumps around
- Big files and small files copy at different speeds. A folder that is mostly video flies along, then crawls when it reaches thousands of tiny files. The estimate follows the current speed, so it lurches each time.
- Some drives start fast and slow down. Many portable drives write quickly for the first few gigabytes and then settle to a lower speed for the rest of a long copy.
- Other work on the same drive. A second copy, a Time Machine backup or Spotlight indexing all share the drive and the cable.
- Network drives vary. Wi-Fi speed changes from minute to minute, and a busy NAS slows down.
Treat the figure as a rough guide early on. It settles down as the copy goes, and the amount copied (“7.6 GB of 12 GB”) is always the more reliable number.
How to see the real copy speed
Open Activity Monitor (in Applications → Utilities) and click the Disk tab. At the bottom, Data written/sec shows how fast your Mac is writing to its drives. For a copy to a NAS or another network drive, use the Network tab and read Data sent/sec instead.
Those figures cover the whole Mac, not one copy, so they are most useful when the copy is the main thing going on.
You can also work it out from Finder alone. Note the amount copied, wait one minute, and note it again. A copy that moves on by 6 GB in a minute is running at about 100 MB a second.
Work out your own estimate
Time is size divided by speed. 100 GB at 100 MB a second is 1,000 seconds, or about 17 minutes. As a rough guide, for large files in good conditions:
- A USB 2 connection (an old port, or a cable that only carries USB 2): about 30 to 40 MB a second. 100 GB takes about 40 minutes to an hour.
- A portable hard drive on USB 3: about 100 to 150 MB a second. 100 GB takes roughly 11 to 17 minutes.
- A portable SSD on USB 3: 400 MB a second or more. 100 GB takes a few minutes.
- A NAS over wired gigabit Ethernet: up to about 110 MB a second. 100 GB takes 15 minutes at best.
- A NAS over Wi-Fi: anything from a fraction of that to about the same, depending on the signal.
Folders with many small files can take several times longer than these figures suggest. If your copy is far slower than the drive should manage, our guide to slow copies to an external drive shows how to check the cable and the connection speed.
Keeping the estimate in view
Cartage does not measure speed or calculate its own time remaining. It mirrors what Finder reports. The menu bar shows how far the copy has got, as a percentage, a slim bar or a ring. Click it and each copy has its own bar with Finder's own status line underneath, the same amount copied and time left that the progress window shows.
That saves digging out the window every time you want to know how long is left, and a short notice appears when the copy finishes. It only covers copies and moves done in Finder. £9.99 once, with a 7-day trial that has every feature and needs no account, card or email.
Try Cartage free for 7 days
Every feature, no card, no account, no email. Then £9.99 once if you keep it. macOS 14 or later.
Questions people ask
Why does the time remaining keep changing when I copy files on a Mac?
Finder bases it on how fast the copy has been going lately. Speed changes with file sizes, the drive and anything else using it, so the estimate changes too. The amount copied is the more reliable figure.
How do I see file transfer speed on a Mac?
Finder does not show it. Open Activity Monitor and read Data written/sec on the Disk tab, or Data sent/sec on the Network tab for a network drive.
How long does it take to copy 100 GB on a Mac?
It depends on the slowest part of the chain. Roughly 11 to 17 minutes to a USB 3 hard drive, a few minutes to a fast SSD, and 40 minutes or more over a USB 2 connection. Many small files take longer.
Does Cartage show copy speed or its own time estimate?
No. Cartage shows the progress Finder reports, including Finder's own status line with the amount copied and time remaining. It does not measure speed.